Interactive training course · 5 days

Ultrasonic Testing (UT) Level I and II

الفحص بالموجات فوق الصوتية (UT) المستويان الأول والثاني

Next date
8–12 March 2027Madrid
Fees from
⁦£2,950⁩per delegate
Formats
Classroom · Online4 sessions
Duration
5 daysCertificate

Overview

Ultrasonic testing is one of the most widely used non-destructive testing methods in the oil, gas, petrochemical and power industries. It is used to measure wall thickness, detect corrosion and erosion, and find and size flaws in welds, plates, forgings and pipework without damaging the component. Reliable ultrasonic inspection depends on a sound understanding of sound wave behaviour, correct equipment calibration, appropriate probe selection and careful interpretation of signals, because poor technique can miss critical defects or lead to unnecessary repairs.

This course provides theoretical knowledge and practical skills in ultrasonic testing at the level typically expected of Level I and Level II technicians. It is an independent course that supports, but does not replace, the employer's written practice; it does not confer certification, which remains the responsibility of the employer or an appropriate certification body. Participants learn the physics of ultrasound, wave modes, reflection and refraction, transducers, couplants, flaw detectors and thickness gauges. The course covers calibration with reference blocks, straight and angle beam techniques, weld inspection scanning patterns, flaw location and sizing, interpretation, acceptance criteria and reporting.

Objectives

  • Explain the physics of ultrasound, wave modes, reflection and refraction
  • Describe transducers, couplants and ultrasonic flaw detector controls
  • Calibrate equipment using reference blocks for straight and angle beam testing
  • Measure thickness and assess corrosion using ultrasonic techniques
  • Inspect welds using angle beam scanning patterns and locate indications
  • Size and interpret indications and apply acceptance criteria
  • Prepare clear ultrasonic inspection reports

Who should attend

NDT technicians, inspection technicians, QA/QC inspectors and engineers needing practical ultrasonic testing skills.

Training methodology

The course combines classroom theory with extensive hands-on practice using ultrasonic flaw detectors, thickness gauges, reference blocks and welded test specimens containing known flaws. Participants calibrate instruments, measure thickness on corroded samples, carry out angle beam scans on welds, locate and size indications and write inspection reports. Short theory and practical tests are used throughout the week to check each participant's progress. The course supports preparation for employer-based qualification but does not itself grant certification. Each day ends with a short quiz and practical review.

Programme outline

Day1Principles of Ultrasonic Testing
  • The role of ultrasonic testing among NDT methods and its typical industrial applications
  • Nature of sound waves, frequency, wavelength, velocity and acoustic impedance
  • Wave modes including longitudinal, shear and surface waves and where each is used
  • Reflection, refraction, mode conversion and Snell's law at material interfaces
  • Attenuation, beam spread, near field and far field and their effect on inspection
  • Advantages, limitations and practical safety considerations of ultrasonic testing on site
  • Practical exercise: calculating refracted angles and near field lengths for common probes
Day2Equipment and Calibration
  • Ultrasonic flaw detectors, their main controls, displays and the A-scan presentation of signals
  • Transducers including straight beam, angle beam and dual element probes
  • Couplants, surface condition and their influence on signal quality and inspection reliability
  • Reference and calibration blocks and their purpose in setting up equipment
  • Time base and sensitivity calibration for straight beam testing using standard reference blocks
  • Angle beam calibration including index point, beam angle and distance amplitude correction
  • Practical exercise: calibrating a flaw detector for straight and angle beam testing
Day3Thickness Measurement and Straight Beam Testing
  • Ultrasonic thickness measurement principles and the use of digital thickness gauges
  • Corrosion and erosion mapping on piping, vessels and storage tanks
  • Straight beam inspection of plates and forgings for laminations and inclusions
  • Effects of temperature, coatings and surface roughness on thickness readings
  • Recording, trending and reporting thickness data to support integrity and remaining life assessment
  • Common errors in thickness measurement and how to avoid them
  • Practical exercise: measuring thickness and mapping corrosion on test samples
Day4Weld Inspection with Angle Beam
  • Weld geometry, common weld defects and their typical ultrasonic responses
  • Scanning patterns for butt welds and the coverage of the weld and heat affected zone
  • Locating indications using sound path, surface distance and depth calculations
  • Sizing techniques including amplitude-based methods and probe movement methods for flaw length
  • Distinguishing relevant indications from geometric echoes and spurious signals on the screen
  • Introduction to advanced methods such as phased array and time of flight diffraction
  • Practical exercise: angle beam scanning of welded specimens with known flaws
Day5Interpretation, Acceptance and Reporting
  • Interpretation and evaluation of indications in welds and base materials
  • Applying acceptance criteria from common construction codes and client inspection specifications
  • Written procedures, technique sheets and the responsibilities of Level I and Level II personnel
  • Preparing clear and complete ultrasonic inspection reports that others can rely on
  • Qualification and certification concepts and the role of the employer's written practice
  • Practical assessment: calibration, scanning, sizing and reporting on a test specimen
  • Final theory assessment and discussion of ultrasonic practices at participants' sites

Dates and fees

8–12 March 2027March 2027
MadridSpain
Open
⁦£5,500⁩
12–16 April 2027April 2027
DammamSaudi Arabia
Open
⁦£4,450⁩
20–24 September 2027September 2027
MuscatOman
Open
⁦£4,450⁩
6–10 December 2027December 2027
OnlineOnline
Open
⁦£2,950⁩

Fees are in GBP. per delegate.

Certificate

Every delegate who attends the full programme receives a Harfard Technology certificate of completion stating the course title, duration, dates and venue.

Frequently asked questions

Will I receive a certificate?
Yes. Every delegate who attends the full programme receives a Harfard Technology certificate of completion.
What is the difference between classroom and online?
The content and trainer are the same. Classroom sessions run in a training venue in the chosen city; online sessions are live with the trainer over the internet.
Can you run this course for our company?
Yes. We deliver the course in-house at your premises or in a city you choose, adapting examples and exercises to your facilities.
How do I register?
Choose a date and click "Register", or send your request from the contact page. Our team will contact you to confirm your seat and send payment details.

Subscribe to our newsletter

New dates and featured courses, once a month.