Piping Stress Analysis
تحليل إجهادات الأنابيب
- Next date
- 22–26 March 2027Online
- Fees from
- £2,950per delegate
- Formats
- Online · Classroom4 sessions
- Duration
- 5 daysCertificate
Overview
Piping systems in refineries, gas plants, petrochemical complexes and power stations must withstand pressure, weight, thermal expansion, vibration, wind, seismic and transient loads throughout their life. Inadequate flexibility or poor support design can overload pump and compressor nozzles, cause flange leaks, crack welds and supports, and lead to fatigue failures. Piping stress analysis ensures that systems are designed to stay within code allowable stresses and equipment load limits, while remaining practical to build and maintain. It is a key skill for piping engineers and an important consideration in plant modifications.
This course provides a practical introduction to piping stress analysis according to recognised process piping codes. Participants learn the types of loads and stresses in piping, sustained, expansion and occasional load cases, allowable stress limits and stress intensification factors. The course covers piping flexibility, support types and locations, expansion loops and joints, nozzle load limits for rotating and static equipment, and flange leakage checks. It also explains dynamic loads such as vibration, water hammer, slug flow and relief valve thrust, the basics of stress analysis software, interpretation of results, the review of stress reports and practical solutions to common problems.
Objectives
- Explain the types of loads and stresses acting on piping systems
- Apply sustained, expansion and occasional load cases and code allowables
- Use stress intensification factors and flexibility principles in design
- Select support types and locations, expansion loops and expansion joints
- Check nozzle loads on pumps, compressors and vessels and flange leakage
- Assess dynamic loads such as vibration, water hammer and relief valve thrust
- Interpret stress analysis software results and review stress reports
Who should attend
Piping and mechanical engineers, design engineers, project engineers, inspection and integrity engineers and designers involved in piping systems.
Training methodology
The course combines explanation of stress analysis principles with hand calculations, isometric drawings and examples from stress analysis software. Participants identify critical lines, calculate thermal expansion and simple stresses, select support arrangements, check nozzle loads against equipment limits and interpret software outputs for sustained, expansion and occasional cases. Typical problems such as overloaded pump nozzles, lifting supports and vibrating small-bore lines are solved in groups. Real stress reports are reviewed to identify errors and missing information. Each day ends with a short quiz and discussion.
Programme outline
Day1Loads, Stresses and Code Requirements
- Why piping stress analysis is needed and the consequences of inadequate flexibility
- Loads on piping: pressure, weight, thermal expansion, wind, seismic and dynamic loads
- Primary and secondary stresses and their different failure modes in piping
- Code requirements for sustained, expansion and occasional load cases and their allowable limits
- Allowable stresses, stress range and the effect of cyclic operation on fatigue
- Selection of critical lines for formal stress analysis using line lists and criteria
- Practical exercise: identifying critical lines on a process unit line list
Day2Flexibility and Stress Calculations
- Thermal expansion calculations and the movement of lines between anchors
- Stress intensification factors for bends, tees and other fittings and how they are applied
- Simple hand methods for checking flexibility and stresses in piping layouts
- Expansion loops, offsets and changes of direction to increase flexibility
- Expansion joints, their types, limitations and the forces they create
- Cold spring and its use and limitations in piping design
- Practical exercise: calculating thermal expansion and checking a simple loop by hand
Day3Supports and Equipment Nozzle Loads
- Support types: rests, guides, line stops, anchors, spring hangers and constant supports
- Support spacing, sustained stress control and the prevention of excessive sag
- Friction effects, lifting supports and the redistribution of loads after start-up
- Nozzle load limits for pumps, compressors, turbines and air coolers
- Nozzle loads on vessels and tanks and the use of local stress methods
- Flange leakage checks under combined pressure, bending and axial loads
- Practical exercise: resolving an overloaded pump nozzle by changing the support arrangement
Day4Dynamic Loads and Vibration
- Types of dynamic loads in piping and why static analysis may not be enough
- Vibration of small-bore connections and practical methods to assess and reduce it
- Water hammer, slug flow and surge loads and how to estimate them
- Relief valve reaction forces and the design of supports for relief systems
- Pulsation from reciprocating pumps and compressors and its effect on piping
- Seismic and wind loads on piping and the use of restraints and snubbers
- Practical exercise: assessing relief valve thrust and selecting suitable restraints
Day5Software, Results Review and Practical Solutions
- Building a stress model: geometry, materials, boundary conditions and load cases
- Interpreting software output for stresses, displacements, support loads and nozzle loads
- Common modelling errors and how to check results for reasonableness
- Reviewing stress reports and the information they should contain for approval
- Stress analysis for plant modifications, tie-ins and hot tapping work
- Group exercise: reviewing a stress analysis report and recommending design changes
- Final assessment and discussion of piping stress issues in participants' projects
Dates and fees
Fees are in GBP. per delegate.
Certificate
Every delegate who attends the full programme receives a Harfard Technology certificate of completion stating the course title, duration, dates and venue.
Frequently asked questions
Will I receive a certificate?
What is the difference between classroom and online?
Can you run this course for our company?
How do I register?
Related courses
Maintenance, Reliability & Asset IntegrityReliability-Centred Maintenance
15–19 March 2027 · Geneva +4 dates
Maintenance, Reliability & Asset IntegrityRotating Equipment: Pumps & Compressors
21–25 June 2027 · Barcelona +3 dates
Maintenance, Reliability & Asset Integrity