Lifting and Rigging Operations Supervision
الإشراف على عمليات الرفع والتعليق
- Next date
- 8–12 March 2027Tokyo
- Fees from
- £2,950per delegate
- Formats
- Classroom · Online4 sessions
- Duration
- 5 daysCertificate
Overview
Lifting operations are carried out every day in oil, gas, petrochemical, construction and offshore operations, using mobile cranes, overhead cranes, offshore pedestal cranes, hoists and a wide range of rigging equipment. Dropped loads, crane overturning, rigging failures and people being struck or crushed are among the most serious hazards in industry. Most lifting incidents are caused not by equipment failure alone but by poor planning, incorrect rigging, weak communication and inadequate supervision. Lifting supervisors therefore play a vital role in making sure every lift is planned, prepared and executed safely.
This course provides the knowledge and practical skills needed to supervise lifting and rigging operations safely. Participants learn the responsibilities of lifting supervisors, the categorisation of lifts and the content of lift plans. The course covers crane types and their capacity charts, ground conditions and outrigger loads, rigging equipment such as slings, shackles, hooks and spreader beams, sling angles, centre of gravity and load calculations. It also explains inspection of lifting equipment, signalling and communication, exclusion zones, lifting near live plant and power lines, tandem and critical lifts, environmental limits such as wind, and the investigation of lifting incidents.
Objectives
- Explain the roles and responsibilities of lifting supervisors
- Categorise lifts and prepare or review lift plans
- Interpret crane capacity charts and assess ground conditions
- Select rigging equipment and calculate sling angles and loads
- Inspect lifting equipment and identify defects and rejection criteria
- Control signalling, communication and exclusion zones during lifts
- Supervise critical and tandem lifts and investigate lifting incidents
Who should attend
Lifting supervisors, crane operators, riggers, banksmen, maintenance and construction supervisors, and HSE staff involved in lifting operations.
Training methodology
The course combines explanation of lifting principles with practical exercises using real lift plans, crane capacity charts, rigging equipment and inspection records. Participants categorise lifts, calculate load weights, centres of gravity and sling tensions, read crane charts and prepare a lift plan for a typical plant lift. Rigging equipment is inspected to identify defects and rejection criteria. Hand signals and radio communication are practised. Videos and case studies of crane overturns and dropped loads are analysed in groups to identify planning and supervision failures. Each day ends with a short quiz.
Programme outline
Day1Lifting Operations and Supervisor Responsibilities
- Types of lifting operations in oil, gas, construction and offshore work and their hazards
- Roles of the appointed person, lifting supervisor, crane operator, rigger and banksman
- Legal requirements, recognised industry standards and company lifting procedures that supervisors must apply
- Lift categorisation: routine, complex and critical lifts and the controls for each
- Lift planning, method statements and the content of a good lift plan
- Pre-lift meetings, toolbox talks and confirming that everyone understands the plan
- Practical exercise: categorising a set of lifts and identifying the planning required
Day2Cranes, Capacity Charts and Ground Conditions
- Types of cranes: mobile, crawler, tower, overhead and offshore pedestal cranes
- Reading crane load charts, radius, boom length and the effect of configuration
- Rated capacity limiters, load moment indicators and other crane safety devices
- Ground conditions, outrigger loads, mats and the risk of crane overturning
- Environmental limits such as wind speed, visibility, temperature and sea state
- Crane set-up, pre-use checks and the documents a crane must carry
- Practical exercise: selecting a crane configuration from load charts for a given lift
Day3Rigging Equipment and Load Calculations
- Wire rope, chain and synthetic slings and their working load limits and uses
- Shackles, hooks, eyebolts, spreader beams and lifting beams and how to select them
- Sling angles, mode factors and the effect of angle on sling tension
- Calculating load weights and locating the centre of gravity of irregular loads
- Protecting slings from sharp edges and controlling loads with tag lines
- Below-the-hook lifting devices and the special care and inspection they require
- Practical exercise: calculating sling tensions and selecting rigging for an awkward load
Day4Inspection, Communication and Lift Execution
- Pre-use inspection of slings, shackles and hooks and the common rejection criteria
- Thorough examination, certification, colour coding and the maintenance of lifting equipment registers
- Hand signals, radio communication and the role of the designated signaller
- Exclusion zones, barriers and keeping people away from suspended loads
- Lifting near live plant, pipe racks and overhead power lines safely
- Stopping a lift when conditions change and the use of stop work authority
- Practical exercise: practising hand signals and inspecting rigging equipment for defects
Day5Critical Lifts and Incident Prevention
- Tandem lifts, blind lifts and lifts over live process equipment
- Personnel baskets and lifting people, and the strict controls they require
- Offshore lifting, supply vessel operations and the effects of motion and wind
- Investigation of lifting incidents and the typical root causes found
- Lessons from crane overturns, dropped loads and rigging failures in industry
- Group exercise: preparing and presenting a lift plan for a critical plant lift
- Final assessment and discussion of lifting challenges at participants' sites
Dates and fees
Fees are in GBP. per delegate.
Certificate
Every delegate who attends the full programme receives a Harfard Technology certificate of completion stating the course title, duration, dates and venue.
Frequently asked questions
Will I receive a certificate?
What is the difference between classroom and online?
Can you run this course for our company?
How do I register?
Related courses
Health, Safety & EnvironmentProcess Safety Management
22–26 February 2027 · Berlin +4 dates
Health, Safety & EnvironmentHAZOP Study Leadership
11–15 January 2027 · Geneva +4 dates
Health, Safety & Environment