Interactive training course · 5 days

Flange Management and Bolt Torquing (ASME PCC-1)

إدارة الشفاه وعزم ربط المسامير (ASME PCC-1)

Next date
1–5 February 2027Geneva
Fees from
⁦£2,950⁩per delegate
Formats
Classroom · Online4 sessions
Duration
5 daysCertificate

Overview

Leaking flanged joints are one of the most common sources of loss of containment in refineries, gas plants and petrochemical facilities, and many leaks occur shortly after maintenance when joints are reassembled. Most flange leaks are not caused by poor design but by damaged flange faces, wrong gaskets, misalignment, poor bolt lubrication, incorrect tightening sequences and insufficient bolt load. A structured flange management programme based on ASME PCC-1 guidance, with trained and competent bolting technicians, can dramatically reduce leaks during start-up and normal operation.

This course provides practical knowledge of bolted flanged joint assembly and flange management based on the guidelines of ASME PCC-1. Participants learn how bolted joints work, the importance of gasket stress and bolt preload, flange types and facings, gasket selection, and bolt and nut materials. The course covers inspection of flange faces and fasteners, alignment tolerances, lubrication, torque and tension calculations, tightening patterns and methods, and the use of hydraulic torque wrenches and tensioners. It also explains joint tagging and records, quality checks, leak testing, hot bolting precautions, bolting competence and effective flange management systems.

Objectives

  • Explain how bolted flanged joints work and why they leak
  • Select flange types, facings, gaskets and fastener materials correctly
  • Inspect flange faces, fasteners and alignment before assembly
  • Calculate target torque and tension values for bolted joints
  • Apply correct lubrication, tightening patterns and tightening methods
  • Use hydraulic torque wrenches and tensioners safely and accurately
  • Implement joint records, quality checks and a flange management system

Who should attend

Mechanical technicians, bolting technicians, maintenance supervisors, inspectors, mechanical engineers and turnaround planners.

Training methodology

The course combines explanation of bolted joint principles with hands-on practice using flanges, gaskets, bolts and torque tools where available. Participants inspect flange faces and fasteners for defects, check alignment tolerances, calculate torque and tension values, prepare tightening sequences and complete joint assembly records. Demonstrations show manual torque, hydraulic torque and tensioning methods and the safety precautions for each. Case studies of flange leaks after turnarounds are analysed in groups to identify root causes. The course builds practical competence but does not itself confer formal qualification. Each day ends with a short quiz.

Programme outline

Day1Bolted Joint Principles
  • The cost and safety impact of flange leaks in process plants and during start-ups
  • How a bolted flanged joint works as a system of flanges, gasket and bolts
  • Bolt preload, gasket stress and the relaxation of joints after assembly
  • Why flanges leak and the most common causes found in plant leak investigations
  • Overview of ASME PCC-1 guidance and how it supports reliable joint assembly
  • Joint criticality and selecting the level of control for different joints
  • Practical exercise: analysing flange leak case studies to identify their root causes
Day2Flanges, Gaskets and Fasteners
  • Flange types such as weld neck, slip-on, blind and lap joint and their facings
  • Flange face finish requirements and acceptable and unacceptable face damage
  • Gasket types, materials and selection for different pressures, temperatures and fluids
  • Gasket handling, storage, identification and the dangers of reuse or substitution
  • Bolt and nut materials, grades, markings, coatings and through-hardened washers
  • Inspection of fasteners for damage, corrosion and correct length and thread engagement
  • Practical exercise: inspecting flange faces, gaskets and fasteners and recording defects
Day3Torque, Tension and Lubrication
  • The relationship between torque, friction and bolt preload in practice
  • Lubricant selection and the effect of lubrication on achieved bolt load
  • Calculating target bolt stress, torque values and tension values for joints
  • Using torque tables and avoiding common errors in torque calculations
  • Bolt yield, gasket crushing and other limits on maximum bolt load
  • Bolt load scatter and how tightening methods affect the uniformity of load
  • Practical exercise: calculating torque and tension values for a set of flanged joints
Day4Assembly Procedures and Tightening Methods
  • Pre-assembly checks, flange alignment tolerances and the safe correction of misalignment
  • Gasket installation and centring and the prevention of gasket damage
  • Tightening patterns and multi-pass procedures recommended by ASME PCC-1 guidance
  • Manual torque wrenches and hydraulic torque wrenches and the importance of regular calibration
  • Hydraulic tensioners, tool coverage requirements and step-by-step tensioning procedures for joints
  • Safety precautions when using hydraulic bolting tools and high pressure equipment
  • Practical exercise: preparing a tightening sequence and assembling a demonstration joint
Day5Quality Control and Flange Management
  • Joint tagging, identification and assembly records for each critical joint
  • Quality checks, independent verification and final sign-off by supervisors and inspectors
  • Leak testing, service testing and the response to leaks during start-up
  • Hot bolting and live joint work, risk assessment and special controls
  • Competence and training of bolting personnel and the role of qualified assemblers
  • Group exercise: designing a flange management system for a plant turnaround
  • Final assessment and discussion of flange issues at participants' own plants

Dates and fees

1–5 February 2027February 2027
GenevaSwitzerland
Open
⁦£6,250⁩
26–30 April 2027April 2027
Abu DhabiUnited Arab Emirates
Open
⁦£4,450⁩
5–9 July 2027July 2027
OnlineOnline
Open
⁦£2,950⁩
4–8 October 2027October 2027
IstanbulTurkey
Open
⁦£4,500⁩

Fees are in GBP. per delegate.

Certificate

Every delegate who attends the full programme receives a Harfard Technology certificate of completion stating the course title, duration, dates and venue.

Frequently asked questions

Will I receive a certificate?
Yes. Every delegate who attends the full programme receives a Harfard Technology certificate of completion.
What is the difference between classroom and online?
The content and trainer are the same. Classroom sessions run in a training venue in the chosen city; online sessions are live with the trainer over the internet.
Can you run this course for our company?
Yes. We deliver the course in-house at your premises or in a city you choose, adapting examples and exercises to your facilities.
How do I register?
Choose a date and click "Register", or send your request from the contact page. Our team will contact you to confirm your seat and send payment details.

Subscribe to our newsletter

New dates and featured courses, once a month.